Thread Break – Crazy Thread!

I was Happily embroidering a couple of nights ago when I got a Thread Break. I am embroidering on some very rough textured Placemats (almost like burlap) for an upcoming Valentine Banquet. As I am using Metallic Thread, I wasn’t terribly surprised because this rough burlapy fabric can be hard on Metallic Thread, even our Rapos “Metallized” Thread that is really wrapped with Mylar instead of actual metallic bits.

When I grabbed the end of the thread to snip a clean end and re-thread the needle, I couldn’t even pull enough thread down to reach the needle!

We embroiderers tend to yell at our embroidery machine when we experience a Thread Break. We blame it on Tension, bad needles, bad fabric, wrong stabilizer . . . you name it. And when it happens repeatedly, we tend to growl and mumble and scowl at our machine and say, “What the heck is wrong with you!!???” In this instance, the problem was my thread. It had gotten itself off its thread path and wrapped itself around the post in the adjacent thread path!

If you have sewn or embroidered for any length of time, you know that thread can do some crazy things. When you get a Thread Break, before you re-thread the needle and press Start – do yourself a favor and check the entire length of the Thread’s Path to verify that all is truly well with the Thread.

What the heck? It’s not the fabric that is the problem here!

I made the two videos below to show you what happened.

The Moral of this Story? When you start experiencing unexplained issues:

  • Check the entire Thread Path – from Thread Spool to Needle.¬†Sometimes, thread can droop off the spool and get itself caught under the spool causing the kind of Thread Break shown in this video. A Thread Net around the spool can keep the Thread from being able to droop down and get caught under the spool. A Thread Net can also prevent the kind of slack in the Thread that allowed it to get over into the adjacent Thread Path and get wrapped around the post.
  • Pull the Thread and make sure it moves freely.
  • As you pull, watch the Thread move through the Thread Path – watch the Tension Dials – are they turning as you pull?
  • Is your needle in Backwards? If you are new to your Happy Machine – coming from the Single Needle/Home Market with Flat-Backed Shank Needles – it is easy to insert your Round Shank Commercial Needles backwards. Guess what? They won’t work when they are in backwards! If you can’t tell the difference, get yourself a magnifying glass and really, really inspect one of your needles. Get familiar with it. Once you look at your needle really closely, you will be able to tell immediately if it is inserted backwards. Doesn’t mean you won’t still put it in backwards from time to time, we all get in a hurry and make mistakes. But, when you do, and you are troubleshooting, you will see the problem right away if you know the back of the needle when it is facing the wrong way – towards you!

Here’s a helpful diagram:needlediagram

Finally,

It is easy to get yourself all worked up when you feel like you are in a battle with your embroidery machine and it is winning! Kind of like trying to get a Toddler to eat his peas. He is winning! But if you will take a deep breath, walk away, calm down and then come back and really, really look at the situation – from top to bottom – you might find that it is just a simple problem like my Crazy Thread!

Sorry, I have no advice on the Toddler – my son never ate his peas – still won’t. ūüôā

 

 

Heading for AQS Quilt Week in Des Moines

Well, I am almost ready for AQS Quilt Week in Des Moines, IA – October 5-8. Did I say almost? Maybe it’s more like, “Oh no! I’m not nearly ready. It’s going to take all night, every night to make my vision come true for the booth!” Well, OK, it is somewhere in between the two.

Come see me and see if I managed to pull it all together.

Will you be at the AQS Quilt Week in Des Moines next month?

I will be in a corner booth just outside the Learning Center so be sure and stop in and say hello.

We will have great prices ‚Äď especially for the AQS Members as part of their ‚ÄúI Am AQS‚ÄĚ program.

Call me anytime for a Price Quote Р877-335-5206, Ext 6532 or email me at smccann@texmacusa.com.

quiltweekdesmoines2016

Small Things – Big Problems

Sometimes it is the smallest things that cause us the biggest problems. A perfect example of this is your Bobbin Case. Many times we hear that someone is experiencing serious issues with stitch outs and after troubleshooting – it’s lint in the bobbin case! This can be extremely frustrating after hours of struggle, trial and error, damaged materials . . . you know . . . I’m sure you’ve been there.

First, let’s be sure that your Bobbin¬†and Bobbin Case are being loaded and inserted properly:

 

BobbinCase1

 

 

BobbinCase2

 

BobbinCase3

 

 

BobbinCase4

 

 

DropTest

A Bobbin Case costs just $12 – https://texmacdirect.com/shop/bobbin-thread/bobbin-case-for-hch-hcs-hcd-hcr-2/

I actually have 4 Bobbin Cases for my Happy HCD2 15 Needle Embroidery Machine.

#1 – Regular Stitching Case – Used for just that – Regular Embroidery Stitching – the kind I do the most.

#2- Metal Bobbin Case – This one has the Anti-BackLash Spring inside it – https://texmacdirect.com/shop/5deals/anti-backlash-spring-2/ ¬†¬† This spring, as explained in the video below, is used when I wind my own bobbins with thread to¬†match the top thread. Since you don’t want this Spring installed if you are not using the Metal Bobbins, I decided to just leave it in the Bobbin Case and swap out Bobbin Cases when I use the Metal Bobbins. I was also afraid I would lose this little Spring and not have it when I needed it – safest place to keep it? – in a Bobbin Case! The Happy Machines do not come with these Metal Bobbins as most of our customers use Pre-Wound Bobbins. If you would like to wind your own Bobbins, you can purchase the Metal Bobbins and the Anti-Backlash Spring at www.TexmacDirect.com

MetalBobbinAndABLS

 

#3 – Quilting Case – This is the Bobbin Case I use when I am¬†Quilting my Quilt¬†Sandwich (Pieced Top/Batting/Backing). When I am¬†Quilting, I need the Tension on the Bobbin Case to be set much looser than the Tension when I am stitching¬†regular embroidery designs. With Quilting, I want the Top and Bobbin Thread to “meet in the middle”. I don’t want to see Bobbin Thread on the Top or Top Thread on the Bottom. I also don’t want to be constantly loosening and re-tightening the screw on my Bobbin Case so I just bought¬†a 3rd Bobbin Case that is set and dedicated to Quilting. I put this Case in a small plastic zip bag with a piece of Quilt Batting in it so I know that it is my Quilting Bobbin Case. I have painted a stripe of nail polish across it as well, as a identifier, that this is not my Regular Bobbin Case – but that will wear off in time. For safety and to avoid confusion, I take that case out, use it and put it straight back in the little bag with the Batting when I finish Quilting. Because¬†I don’t like having to¬†“mess” with my Tension Dials, I have dedicated Needle 1 on my machine to Quilting. The Tension Dials for this Quilting Needle are set very, very tight, allowing them to¬†pull the loosened Bobbin Thread towards the Top, allowing them to¬†meet in the middle for a beautiful Quilting Stitch on my Quilts.

QuiltingTensions

#4 – Emergency Case – Just like the Spare Tire in my car for emergency, unexpected Flat Tires, this is ¬†my “Spare” Bobbin Case – the Tension on this case is set the same as the Tension on my “Regular Stitching Case”, the kind of stitching I do the most. If I have a problem with my Regular Case¬†– like drop it and step on it, kinda flattening it out on one side (don’t ask) – I don’t have to mess with one of my “Specialty” cases, I just pull out my Spare and keep right on stitching! You know, you don’t have to step on it to get it “out of round”, just dropping it can cause that (Don’t Ask!)

4 Bobbin Cases!? Sound like “overkill”?

Well, look at it this way, if you have a needle problem you can simply move the thread to a different needle and keep right on stitching. But, if the problem is the Bobbin Case, what are you gonna do? All the needles use that one Bobbin Case!

Get a spare! I hope you never have to thank me!! ūüôā

As I said at the beginning, believe it or not, just a¬†little bit of fuzz or thread under the Tension Flap on the Bobbin Case could be the entire cause of your current Stitchout Nightmare! (DON’T ASK – REALLY – DON’T ASK!)

This video is one of our Education Manager, Rene Rosales, videos on YouTube. This is one of the setup videos for our HCD2 15 Needle machine – about halfway through this video, Rene shows up close inserting the bobbin in the bobbin case and re-loading it into the machine:

Below is a video on Inserting and Cleaning your Bobbin Case by Bill Garvin: